www.fairchildsemi.com rev. 1.0.2 6/27/02 video features integrated video low pass reconstruction ?ter integrated output driver provides a low impedance output and delivers 2vp-p (6db gain) composite video into 150 ? . 7.1mhz 4 th order video ?ter 0.4% differential gain with 0.4?differential phase integrated dc restore / clamp circuitry applications cctv dvd players televisions hdtv personal video recorders (pvrs) video on demand (vod) cable and satellite set top boxes general description the fms6413 single channel video filter ?driver chip offers comprehensive video ?tering for set top box or dvd applications. this part consists of a 4 th order video low pass ?ter for video ?tering. this device integrates a video driver so that it can directly drive to the outside world. there is also an integrated clamp circuit that allows the part to dc restore. the video output is ?tered at 7.1mhz and buffered to drive 2vp-p into an ac coupled 150 ? load with up to 35pf of load capacitance at the output pin. the ?ter approximates a 4th-order butterworth characteristic with an optimization toward low overshoot and ?t group delay. likewise, the driver is capable of driving a 75 ? load at 1vp-p. there is an option for the video output to be dc coupled which limits the drive to 1 output. block diagram video_in video_out sync strip, reference, and timing gm x2 1v fms6413 single channel video driver with integrated filter and clamp
fms6413 2 rev. 1.0.2 6/27/02 pin con?uration pin description video section power/ground pins pin# pin type description 1 video_in input video input 8 video_out output video output: this pin is the filtered video output pin# pin type description 7 vcc_video power +5 vdc for video 3 gnd_video power ground for video 4 nc nc reserved (need to float) 5 nc nc reserved (need to float) 6 nc nc reserved (need to float) 2 nc nc reserved (need to float) video_in 1 nc 2 3 gnd_video 4 nc video_out vcc_video nc nc 8 7 6 5 fms6413 8-pin soic (s08)
fms6413 rev. 1.0.2 6/27/02 3 functional description introduction the fms6413 is a monolithic continuous time video ?ter - driver designed for reconstructing the video signals from a d/a source. this chip is intended for use in applications with ac coupled input and ac coupled outputs. (see figure 1) the reconstruction ?ter approximates a 4th-order butterworth characteristic with an optimization toward low over-shoot and ?t group delay. the video output is capable of driving 2vp-p into an ac coupled 150 ? video load, with up to 35pf of load capacitance at the output pin. the channel is clamped during sync to establish the appropriate output voltage swing range. thus the input coupling capacitor does not behave according to the conventional rc time constant. clamping for the video channel settles to less than 10mv within 5ms of a change in video input source. in most applications the input coupling capacitor is 0.1?. the input typically sinks 1? during active video, which nominally tilts a horizontal line by about 2mv at the video output. during sync, the clamp typically sources 20? to restore the dc level. the net result is that the average input current is zero. any change in the input coupling capacitor s value will inversely alter the amount of tilt per line. such a change will also linearly affect the clamp response time. this product is robust and stable under all stated load and input conditions. capacitive bypassing vcc directly to ground ensures this performance. video i/o the video input is driven by either a low impedance source of 1vp-p or the output of a 75 ? terminated line. the input is required to be ac coupled via a 0.1? coupling capacitor which allows for a settling time of 5ms. the video output is capable of driving an ac coupled 150 ? load at 2vp-p, or 1vp-p into a 75 ? load. up to 35pf of load capacitance (at the output pin) can be driven without stability or slew issues. the output is ac coupled with a 220? or larger ac coupling capacitor. typical applications diagram figure 1. 1 nc (reserved) 2 3 gnd_video 4 nc (reserved) nc (reserved) nc (reserved) vcc_video 8 7 6 5 fms 6413 sync strip, ref, and timing gm x2 1v video_in video_in video_out video_out 0.1 f 220 f 1 f 0.1 f video cable 75 ? 75 ? +5.0v
fms6413 4 rev. 1.0.2 6/27/02 absolute maximum ratings (beyond which the device may be damaged) note: functional operation under any of these conditions is not implied. performance and reliability are guaranteed only if operating conditions are not exceeded. operating conditions parameter min max units vcc_video (positive dc supply voltage) +6.5 v gnd_video (negative dc supply voltage) v analog and digital i/o gnd-0.3 vcc+0.3 v output current (continuous) 60 ma junction temperature 150 ? storage temperature range -65 +150 ? lead temperature (soldering, 10s) 260 ? thermal resistance ( ja ) 115 ?/w parameter min typ max units temperature range 0 70 c vcc_video range 4.75 5.0 5.25 v gnd_video 0 v icc (+5 vdc) 60 ma
fms6413 rev. 1.0.2 6/27/02 5 electrical characteristics 1vp-p signal at room temperature notes: 1. peaking capacitor increases video output at 4.2mhz nominally by 0.7db 2. sustained short circuit protection limited to 10 seconds video characteristics - unless otherwise noted, typical output loading on video output is 150 ? . symbol parameter condition vcc_video=+5.0v 5% min typ max units av low frequency gain (video_out) at 400khz 6.0 db video_out output level (during sync) sync present on yin 1.0 v tclamp clamp response time settled to within 10mv,0.1? cap on video_in 5ms f1db ?.0db bandwidth (flatness) (video_out) no peaking cap (note 1) 4.0 4.5 mhz fc ?db bandwidth (flatness) (video_out) 6.7 7.1 mhz fsb stopband rejection (video_out) fin = 27mhz to 100mhz worst case -37 -42 db vi input signal dynamic range ac coupled 1.3 1.4 vp-p isc output short circuit current (all channels) video_out to gnd 40 80 ma cl output shunt capacitance video_out 35 pf dg differential gain video_out 0.4 % dp differential phase video_out 0.4 thd output distortion (all channels) video_out = 1.8vp-p at 3.58/ 4.43mhz 0.8 % psrr psrr (all channels) 0.5vp-p (100khz) at vcc -40 db snr ntc-7 weighting 4.2 mhz lowpass -75 db tpd group delay 100khz 70 ns ? tpd group delay deviation from flatness to 3.58mhz (ntsc) 9 ns to 4.43mhz (pal) 7 ns
fms6413 6 rev. 1.0.2 6/27/02 mechanical dimensions inches (millimeters) pin 1 id seating plane 0.189 - 0.199 package: s08 8-pin soic (4.80 - 5.06) 8 1 0.148 - 0.158 (3.76 - 4.01) 0.055 - 0.061 (1.40 - 1.55) 0.012 - 0.020 (0.30 - 0.51) 0.004 - 0.010 (0.10 - 0.26) 0.015 - 0.035 0 - 8 (0.38 - 0.89) 0.006 - 0.010 (0.15 - 0.26) 0.059 - 0.069 (1.49 - 1.75) 0.017 - 0.027 (0.43 - 0.69) (4 places) 0.228 - 0.244 (5.79 - 6.20) 0.050 bsc (1.27 bsc)
fms6413 life support policy fairchild s products are not authorized for use as critical components in life support devices or systems without the express written approval of the president of fairchild semiconductor corporation. as used herein: 1. life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. 2. a critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. www.fairchildsemi.com 6/27/02 0.0m 004 stock#ds30006413 ? 2002 fairchild semiconductor corporation disclaimer fairchild semiconductor reserves the right to make changes without further notice to any products herein to improve reliability, function or design. fairchild does not assume any liability arising out of the application or use of any product or circuit described herein; neither does it convey any license under its patent rights, nor the rights of others. ordering information part number temperature range package FMS6413CS 0 to 70 8 pin soic (s08) FMS6413CSx 0 to 70 tape and reel
|
